Unfortunately, I do not.
When I do the routine maintenance, I just grab the 1/4" ratchet and the whole set of torx bits.
One of them works.
I can't tell you which one without pulling a head off,which it sounds like you are going to do anyway.
| On drums... http://ondrums.net/forum/ |
|
| ANYONE KNOW THE SPEC... http://ondrums.net/forum/viewtopic.php?f=3&t=906 |
Page 1 of 1 |
| Author: | Gregory [ Sun May 20, 2012 11:36 am ] |
| Post subject: | ANYONE KNOW THE SPEC... |
What size driver is required for the Designer lug to shell retaining screws? |
|
| Author: | cliff [ Sun May 20, 2012 11:58 am ] |
| Post subject: | Re: ANYONE KNOW THE SPEC... |
Unfortunately, I do not. When I do the routine maintenance, I just grab the 1/4" ratchet and the whole set of torx bits. One of them works. I can't tell you which one without pulling a head off,which it sounds like you are going to do anyway. |
|
| Author: | Gregory [ Sun May 20, 2012 12:52 pm ] |
| Post subject: | Re: ANYONE KNOW THE SPEC... |
cliff wrote: One of them works. I can't tell you which one without pulling a head off,which it sounds like you are going to do anyway. Yes, anyway, but I wasn't planning to go to Sears with the shell to find out! |
|
| Author: | bigtone23 [ Mon May 21, 2012 2:24 pm ] |
| Post subject: | Re: ANYONE KNOW THE SPEC... |
I dug out the driver I use, but it's unlabeled for size.  I do believe it's a T20 or T25. Wish I could be more specific. I bought the pair of drivers I have years ago for something like $6 new at a big box hardware store. You may be able to do as I did and back a screw out with a small flat head screwdriver and take that to the store for sizing. |
|
| Author: | Gregory [ Mon May 21, 2012 2:31 pm ] |
| Post subject: | Re: ANYONE KNOW THE SPEC... |
Thanks, Chris. I suppose I could break the bank and haul one of these home... http://www.harborfreight.com/100-piece- ... 91310.html |
|
| Author: | tim [ Mon May 21, 2012 3:25 pm ] |
| Post subject: | Re: ANYONE KNOW THE SPEC... |
I think its a t25, I just tried a t27 and it was just too big, all my other torx bits are at work. Just for your info the only thing I have ever used a 27 for was to adjust the legs on a miele dishwasher, I will probably only ever use it for that purpose, but the screwdriver was only 5 bucks. Get crazy and get one of these http://festools-online.com/index.php/498796-festool-centrotec-installers-bit-set.html?gclid=CPHBkfuakrACFUdN4AodXkbMpg you think Sonor drums get expensive, try this stuff for woodworking. Worth every penny though |
|
| Author: | cliff [ Mon May 21, 2012 3:54 pm ] |
| Post subject: | Re: ANYONE KNOW THE SPEC... |
Gregory wrote: Thanks, Chris. I suppose I could break the bank and haul one of these home... http://www.harborfreight.com/100-piece- ... 91310.html Good idea! The next time we get there, you'll be sitting in the middle of the parking lot with everything you own disassembled and sorted into two piles: • Magnetic • Non-magnetic  
|
|
| Page 1 of 1 | All times are UTC - 6 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|