On drums...

For drummers to exchange knowledge, ideas, opinions & equipment...
It is currently Mon Dec 02, 2024 7:50 am

Board index » Drums, Cymbals & Hardware

All times are UTC - 6 hours [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 
  Print view Previous topic | Next topic 
Author Message
Goki
 Post subject: Need an advice - HELP
PostPosted: Fri Oct 22, 2010 1:49 am 
Offline
User avatar

Joined: Mon Mar 08, 2010 11:56 am
Posts: 1524
Location: Skopje, Republic Of Macedonia
I ordered bass drum feet for a friend, to convert an 18" floor tom...
http://www.stdrums.de/hardware/BDfeet/feet37long.JPG

Unfortunately, they don't go through the Yamaha feet holder (don't know how else to call it). I think they're 0.5mm thicker... :S
I got them from St Drums, but replacing those would cost 60euro (shipping both ways).

Is there a chance of taking them to a metal workshop to get them thinned down?!?
We DO NOT wanna drill the feet holders... :(


Suggestions?!?

_________________
Goki - short from Goran :)

Let the good drums roll!!!
Top
 Profile  
 
Jeff
PostPosted: Fri Oct 22, 2010 4:07 am 
Offline

Joined: Wed Apr 07, 2010 4:00 am
Posts: 437
Goki, if you can find out what the screw spacings on the leg blocks are, you can get 2 after market matching F/tom blocks to drill (IF NEEDED) and fit to the shell in the same holes.
Just have to swap them over, and the originals will be just that, still original.
If the spacings are similar to Tama, I might be able to help.

Cheers

_________________
Jeff
Gots ta luv da Beech
Australia
Top
 Profile  
 
Goki
PostPosted: Fri Oct 22, 2010 8:58 am 
Offline
User avatar

Joined: Mon Mar 08, 2010 11:56 am
Posts: 1524
Location: Skopje, Republic Of Macedonia
Thanx Jeff - but finding hardware parts is NOT an option here...
We have to order - if we do, it would be thinner bass drum feet...


I'll see a machine worker tomorrow - we'll see if he can make those bass drum feet thinner...

_________________
Goki - short from Goran :)

Let the good drums roll!!!
Top
 Profile  
 
cliff
PostPosted: Fri Oct 22, 2010 10:01 am 
Offline
User avatar

Joined: Sun Mar 07, 2010 9:57 am
Posts: 1607
Hey Goki,

Tough to see a lot of detail from the photo, but it looks like the legs have some sort of fritction enhancing pattern machined on them, and then chromed.

I don't know how you would take down outside diameter, except for lathing, and not sure how you do that with angled rods. Also not sure you want to lathe off the plating.

You might try this question on Speaking of Drums... I think Mike is pretty knowledgeable interms of machining.

_________________
Cliff

River City Trio

What if we did all have the same opinions?
Top
 Profile  
 
Goki
PostPosted: Fri Oct 22, 2010 11:30 am 
Offline
User avatar

Joined: Mon Mar 08, 2010 11:56 am
Posts: 1524
Location: Skopje, Republic Of Macedonia
Latest updates - a little grease did the trick... :D

But, my friend doesn't like how "tall" the new bass drum is... As far as I know, he needed extra short bass drum legs in order to make it lie on the ground...
That's the problem with all modified floor toms - unless You re-drill the leg holders... :S

_________________
Goki - short from Goran :)

Let the good drums roll!!!
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 

Board index » Drums, Cymbals & Hardware

All times are UTC - 6 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 3 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group